![]() |
|
#1
|
|||||
|
|||||
![]() Thank guys for the constructive input.
![]() I am not totally done with the fans just yet. Martin & I were checking them before he left for Ireland for Xmas & we both think there will be enough air flow to go around but I have been thinking of adding a 3rd fan & adding in some pieces to direct the air flow into all fins. I haven't picked up the AlumiFix yet but need to this week so I can work on them over the holidays. Also have to build the frame to support the heat sink. I will be putting optics on all the whites ( 45 degree ) & blue ( 60 degree ) but not on the Reds or Greens. My heat sinks well be between 10" - 12" above water level & I doubt it very highly that they will be ever at 100%. Martin also supplies the Arctic Siler to attach the LEDs to the heat sink so that's covered too.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#2
|
||||
|
||||
![]() How long does it take that to set up?
|
#3
|
|||||
|
|||||
![]() If youare asking the set time for the glue,as I recall after mixing you only have 5 working minutes and it starts to set I beleive full cure takes 4 hours
|
#4
|
|||||
|
|||||
![]() Sorry forgot to address that question.
From what Martin was saying, just mix up about the size of a dime or smaller at a time because there's only about 10 min working time. Also you only need a dab about 1/8" diameter under each LED, use a toothpick to apply on each LED.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#5
|
|||||
|
|||||
![]() Do you have to prep the aluminum first before gluing the leds on?
__________________
Ross 9 Gallon Nano, Modular LED Lights 14 Gallon BioCube w/ Rebel LED Lights 67 Gallon Mixed Reef, Modular LED Lights Send in the Clowns - Clown Fish Breeding 5 Gallon Fry Hatchery and 15 Gallon Clown Grow Out Tank Last edited by Ross; 12-21-2011 at 03:15 PM. |
#6
|
|||||
|
|||||
![]() Other then making sure the surface if free of any dust or dirt no prep needed.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#7
|
||||
|
||||
![]() this looks awesome
__________________
155 gallon bow front |
#8
|
||||
|
||||
![]() Most guys use a car or a truck.
How do you plan on compensating for that with an LED light? Anyways looks like it going to be pretty awesome, enjoy the project!
__________________
120 gallon, 50 gallon sump, Vertex Illumina 260, Vertex Alpha 200, Vertex UF-20 x 2, Vortech MP60w ES x 2, Eheim 1262, Neptune Apex Controller with PH, Salinity, ORP, Tunze Auto-Top Off, Last edited by azulikit; 12-22-2011 at 05:14 AM. |
#9
|
|||||
|
|||||
![]() Quote:
![]() |
#10
|
|||||
|
|||||
![]() I ended up with carclo frosted white (wide) optics. It's insane how well they direct the light without really spotting. My lights are 12" from the water.
|