Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Reef

Reply
 
Thread Tools Display Modes
  #1  
Old 06-25-2008, 03:31 PM
christyf5's Avatar
christyf5 christyf5 is offline
Staff
 
Join Date: Aug 2001
Location: Nanaimo
Posts: 9,175
christyf5 is on a distinguished road
Default

Quote:
Originally Posted by jkhchris View Post
I figured it would take a long time as well. I have a few rocks that have alot of mushrooms that have grown out of the rock. I still want to keep the rock so I am going to have to chip them off as I move them out of the old tank. I also have a few SPS that have encrusted the rock that will need to be removed as well. All this will be quite time consumming.
Chris

Oh definitely, even without all the fiddly parts its still a good 6 hours from start to finish and that was the fastest I'd ever done it without moving from one house to another. By then I was pretty good at it though (I ripped my tank down 3 times in one year battling dinoflagellates).
__________________
Christy's Reef Blog

My 180 Build

Every electronic component is shipped with smoke stored deep inside.... only a real genius can find a way to set it free.
Reply With Quote
  #2  
Old 06-25-2008, 03:52 PM
Chowder's Avatar
Chowder Chowder is offline
Member
 
Join Date: Jan 2006
Location: Surrey BC
Posts: 1,426
Chowder is on a distinguished road
Default

Is there any way other then scrubbing and a good swish in a bucket to get rock cleaned quickly in the transfer?
Reply With Quote
  #3  
Old 06-25-2008, 04:13 PM
Jason McK's Avatar
Jason McK Jason McK is offline
Member
 
Join Date: Mar 2003
Location: Ladner,BC
Posts: 3,032
Jason McK is on a distinguished road
Default

Chris, Could you pressure wash the rock?
have it in salt water then pull it out spray it with a pressure washer then right back into SW?

J
__________________
My old Tank Shut down Jan 2011
New 220G build about to start
Reply With Quote
  #4  
Old 06-25-2008, 04:23 PM
christyf5's Avatar
christyf5 christyf5 is offline
Staff
 
Join Date: Aug 2001
Location: Nanaimo
Posts: 9,175
christyf5 is on a distinguished road
Default

Quote:
Originally Posted by Jason McK View Post
Chris, Could you pressure wash the rock?
have it in salt water then pull it out spray it with a pressure washer then right back into SW?

J
Even if you take it outside, quickly pressure wash it with regular water, then swish it around in some saltwater and put it back in the tank you won't see much if any of a cycle. I've done it twice with success
__________________
Christy's Reef Blog

My 180 Build

Every electronic component is shipped with smoke stored deep inside.... only a real genius can find a way to set it free.
Reply With Quote
  #5  
Old 06-25-2008, 04:37 PM
Jason McK's Avatar
Jason McK Jason McK is offline
Member
 
Join Date: Mar 2003
Location: Ladner,BC
Posts: 3,032
Jason McK is on a distinguished road
Default

Quote:
Originally Posted by christyf5 View Post
Even if you take it outside, quickly pressure wash it with regular water, then swish it around in some saltwater and put it back in the tank you won't see much if any of a cycle. I've done it twice with success
I thought if anyone had it would have been you. Did it resolve the problem?

J
__________________
My old Tank Shut down Jan 2011
New 220G build about to start
Reply With Quote
  #6  
Old 06-25-2008, 04:51 PM
christyf5's Avatar
christyf5 christyf5 is offline
Staff
 
Join Date: Aug 2001
Location: Nanaimo
Posts: 9,175
christyf5 is on a distinguished road
Default

It resolved the caulerpa problem (for a time) and kicked the arse of the dinoflagellates (however at that time I also removed my sandbed so who knows what did the trick). Plus its damned satisfying watching all that ugliness peel of the rock like melted bugger. In the archives of my blog, I see that I did have a bit of a cycle (I kind of went a little gung ho with the powerwashing as my rocks were pretty nasty) but the algae was confined to the rocks and sandbed and was gone within 2 weeks.
__________________
Christy's Reef Blog

My 180 Build

Every electronic component is shipped with smoke stored deep inside.... only a real genius can find a way to set it free.
Reply With Quote
  #7  
Old 06-25-2008, 07:13 PM
fishoholic's Avatar
fishoholic fishoholic is offline
Member
 
Join Date: May 2007
Location: Edmonton
Posts: 4,137
fishoholic will become famous soon enough
Default

We moved our 65g into a 120g (two years ago) and in Jan. we moved our 120g and 30g into a 230g. Each move took us one day to do.

First (a few days before the move) we filled up the new larger tank with new sand and mostly new water. Then we seeded the new sand with some of the old sand and added a little bit of the old water and ran the skimmer to clear up the water.

On the day of the move we put all the LR into rubbermaid containers that were 1/2 filled with SW, power heads and heaters. We had the large rubbermaid containers set up in front of the new tank and we used buckets to transfer the rock over from the old tank to the rubbermaids. Then we transfered all the fish into a different rubbermaid that had a couple of LR pieces, a heater, a bubbler and a power head in it.

Then we placed/set up the LR in the new tank and after we had it the way we liked it, we added the fish.

The move was a lot of work and it did take all day but the move went very smoothly and we didn't loose any corals or fish.
__________________
One more fish should be ok?, right!!! - Laurie
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 06:49 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.