|
|
|
|
|
#1
07-08-2015, 07:17 PM
|
||||
|
||||
I had a very similar issue about 6 months ago. Could not figure out what it was. But I do remember it broke the GFI in the same time and fashion. I swapped out the GFI for a regular duplex. No harm came of it, but I did not like the idea of not having a GFI installed when walking get on a wet floor, so I installed a new one a month or so later. All was goodoing for about 4 months or so until Sunday....
|
|
#2
07-08-2015, 07:27 PM
|
|||||
|
|||||
|
You might be on to something with the chiller and if you know one of the bars is at 12 amps, that's getting a bit tight. It's generally recommended to keep draw to 80% of maximum on any given 15 amp circuit for your own safety. Wall mounted GFCIs have improved & the newer ones shouldn't be as prone to nuisance trips, but nothing is foolproof!
Have a look at my earlier post, #17, you may have missed that in the process of writing your most recent reply. The reference manual is very comprehensive, an amazing little piece of kit this Apex. You almost need to hire someone to set it up if you wish to use all of it's capabilities!
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build  http://www.canreef.com/vbulletin/showthread.php?t=82206
|
|
#3
07-08-2015, 07:39 PM
|
|||||
|
|||||
|
The Apex Reference Manual is full of little gems! Remember my questioning of a logged current spike of 75 amps?
https://www.neptunesystems.com/downl...nce_Manual.pdf Page 139 "EB8 or EB4 shows incorrect amperage Similar to the previous issue, the EBx may need recalibration. The process is simple but you must be comfortable knowing how to telnet into your controller. If so, then read on. 1. Identify the Aquabus number of the EB8 or EB4 that you want to calibrate. If your EBx is numbered EB8_3 then the Aquabus number is 3. 2. Unplug everything from the EBx or at least make 100% certain it’s all turned off. This is critical. Whatever amperage the EBx is pulling when the calibration is run becomes the new zero point. You want to make sure it’s pulling 0. 3. Telnet into the controller and login with your userid and password. 4. Issue the following command: eb8zero n where ‘n’ is the Aquabus number of the EBx you want to calibrate. If you’re calibrating an EB4, the command is still ‘eb8zero’. So using the above example of an EB that is known as ‘EB8_3’ the command would be ‘eb8zero 3’. This command is case sensitive and should be entered in lower case as is shown. It executes immediately and there’s no confirmation or message when finished, just a new telnet prompt. 5. Quit telnet. That’s it. Your EBx should now read the proper amperage load when devices are active."
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206
|
|
#4
07-08-2015, 09:37 PM
|
||||
|
||||
|
[quote=mike31154;958337]The Apex Reference Manual is full of little gems! Remember my questioning
Hey, good one Mike. You may be onto something here... I do not remember reading that, but will now. Now to learn what and how to telnet...Whoever said having a saltwater tank is easy was lying....
|
|
#5
07-08-2015, 09:53 PM
|
||||
|
||||
|
Bah, telnet will be easy compared to everything else
|
|
#6
07-08-2015, 10:17 PM
|
||||
|
||||
|
So far , with the MH light plug removed from the EB8, the amps are steady at 11.3 max amps..
|
|
#7
07-08-2015, 11:30 PM
|
||||
|
||||
|
Mike, good to see you have way more time than me to help out with this problem.
 I would put the chiller on its own circuit and not run it on the apex. They can draw a fair bit of current when they startup. Magnetic ballasts will draw more current when they strike the bulb than a electronic ballast. The running current should be close, but the magnetic ballast will use more power. Definitely recalibrate the eb8.
|
|
#8
07-08-2015, 09:31 PM
|
||||
|
||||
|
Quote:
Thanks for the ideas and helping working it down to possible issues and solutions
|
Hybrid Mode
