Time for LEDs?

MMAX · #1 01-30-2012, 10:00 PM

Quote:

Originally Posted by sphelps

Some of us must have different definitions of plug and play. Modular LEDs are no different than other DIY leds besides not requiring soldering although there are also non-soldering options available for other LED boards as well. Regardless the modular LEDs still have to be mounted to an appropriately sized heat sink which has to be cooled with fans and mounted some how above your tank. The LEDs then have to be connected in series appropriately and connected to multiple drivers (ideally with a soldered connection) which also have to be mounted somewhere. Then drivers may or may not need to be tuned to the correct current, either way some basic knowledge about the subject is needed. Then you have to configure the 0-10V or PWM dimming signal to some kind of controller which isn't always that easy for even technical minded people. I don't know about you but I don't see how this falls under plug and play...

That's cause Martin does all that stuff for you. You mount it into your hood, plug it in and away you go.

fishytime · #2 01-31-2012, 12:18 AM

what if you dont have a hood/canopy?..... or the skills/tools to make one?.....then your left with an unsightly diy LED, however easy it may be to assemble.....

sphelps · #3 01-31-2012, 01:38 AM

Quote:

Originally Posted by MMAX

That's cause Martin does all that stuff for you. You mount it into your hood, plug it in and away you go.

Only if you pay for it, I think someone that was unsure about how these work would be better off putting that extra cash towards a fixture with warranty rather than a DIY system that they no nothing about as it was put together by someone else. I'm sure he's a good guy and all but is this a career path, will he be around to service such items in the future?

Blue Ram · #4 01-31-2012, 02:03 AM

Update - I will have my new lighting delivered on Friday the 3rd. After a lengthy conversation with Martin, I ordered 3 blue Sols. Total cost including rails, cable kit & taxes - under $1500.
I appreciate all the comments provided by everyone and I considered each one of them in my decision.
DIY may have saved some money but it required assembly and skills I do not have.

sphelps · #5 01-31-2012, 02:05 AM

Cool, ramp them up slowly

MMAX · #6 01-31-2012, 03:07 AM

Quote:

Originally Posted by sphelps

Only if you pay for it, I think someone that was unsure about how these work would be better off putting that extra cash towards a fixture with warranty rather than a DIY system that they no nothing about as it was put together by someone else. I'm sure he's a good guy and all but is this a career path, will he be around to service such items in the future?

I didn't pay any extra for it. I guess it doesn't matter anymore does it?

kien · #7 01-31-2012, 03:16 AM

Quote:

Originally Posted by MMAX

I didn't pay any extra for it. I guess it doesn't matter anymore does it?

I didn't know that Martin would assemble the units for you free of charge, that's a sweet deal! I will have to contact him for my LED project. Thanks for the info.

The Grizz · #8 01-31-2012, 03:26 AM

Quote:

Originally Posted by Blue Ram

Update - I will have my new lighting delivered on Friday the 3rd. After a lengthy conversation with Martin, I ordered 3 blue Sols. Total cost including rails, cable kit & taxes - under $1500.
I appreciate all the comments provided by everyone and I considered each one of them in my decision.
DIY may have saved some money but it required assembly and skills I do not have.

Very good choice too, I have seen these in person and they are a nice light. You will be very happy.

Quote:

Originally Posted by kien

I didn't know that Martin would assemble the units for you free of charge, that's a sweet deal! I will have to contact him for my LED project. Thanks for the info.

You better mester