Fish tank in condo

[steve fedyk]

Most newer buildings are designed to hold 250 lbs per square foot, anywhere on the floor. If your wall you wont to put the tank on the outside of your place you should have no problems. Most condos are the same floor plan up and down, so if you put it next to the wall there should be a wall right below your wall.
If you build your own stand line it with rubber to catch any spills. Thats what I did and work pretty good.

[lorenz0]

Thanks, thats exactly what I have been thinking.

This system will be set up identical to my 60gal, in over 2 years I never had a flood. Only thing I need to consider is the volume of water that is in my overflow and making sure that it will fit into my sump once the pump turns off. Will be installing a check valve on the return again. And of course buying insurance this time. But I like the liner Idea, could always seal the bottom just in case though.

But I have been thinking tonight and might bump it down a foot to being another 48" long tank. Which will drop the weight down by about 150 pounds of dead weight. Plus t5 bulbs are more accessible

[sphelps]

Originally Posted by steve fedyk

Most newer buildings are designed to hold 250 lbs per square foot, anywhere on the floor. If your wall you wont to put the tank on the outside of your place you should have no problems. Most condos are the same floor plan up and down, so if you put it next to the wall there should be a wall right below your wall.
If you build your own stand line it with rubber to catch any spills. Thats what I did and work pretty good.

Not sure if that's accurate, as far I know the typical load limits for residential is 40lbs/sqft. But this is based on room size, so if the room is 10' x 10' then it can safely support up to 4000lbs total. This is typically just a rule of thumb and more for the upper limit you should never exceed. For something more accurate you need to know the type, size, spacing and span of the floor joists as well as how they are supported. However a tank that size won't be a problem. If it was me I would also secure the stand into the wall at half load even if it's not load bearing, this will help distribute the load better.

[phi delt reefer]

Originally Posted by sphelps

Not sure if that's accurate, as far I know the typical load limits for residential is 40lbs/sqft. But this is based on room size, so if the room is 10' x 10' then it can safely support up to 4000lbs total. This is typically just a rule of thumb and more for the upper limit you should never exceed. For something more accurate you need to know the type, size, spacing and span of the floor joists as well as how they are supported. However a tank that size won't be a problem. If it was me I would also secure the stand into the wall at half load even if it's not load bearing, this will help distribute the load better.

is the 40lb rating for an "unsupported" span? I weight 230lbs and could stand in a space that one foot square with no flex in my floor but i have joists every 16 or 24" (whatever minimum code is).

I would also apply a sheet of 3/4" plywood to the bottom of the stand to distribute the wieight over the entire footprint vs. contact points of the legs. You could also oversize the stand (ie. make it 6" bigger on all sides of the tank) to reduce the lbs/sqft.

[sphelps]

Originally Posted by phi delt reefer

is the 40lb rating for an "unsupported" span? I weight 230lbs and could stand in a space that one foot square with no flex in my floor but i have joists every 16 or 24" (whatever minimum code is).

I would also apply a sheet of 3/4" plywood to the bottom of the stand to distribute the wieight over the entire footprint vs. contact points of the legs. You could also oversize the stand (ie. make it 6" bigger on all sides of the tank) to reduce the lbs/sqft.

The 40lbs/sqft is based on room size and the total weight a given size room has to handle at a minimum. I also believe it's based on dead weight and not live weight.

If you have a solid floor the plywood isn't needed, but if you have tile or carpet it can be a good idea however it could make it harder to level. Typically I usually go with an extruded perimeter on the base which essentially does the same thing but it'll be more stable and easier to level.

[toytech]

Get about 6 of your freinds to stand in the spot your thinking about putting your tank , get the to bounce up and down on the floor and see if you can feel it move ( or if your bottom neibour ends up with a skylight ) . Also your condo board should be able to tell you how much weight the floor can handle , as well as if you are even alowed a tank that big .

[CaptainYooh]

Some condominium corporation By-Laws have specific pet prohibition provisions limiting the number and size of pets homeowners/residents are allowed to keep in their homes. Sometimes these provisions include limitations on aquarium sizes. It's not only the physical design and structural load capacity that is a concern but also a risk of corporation's liability for potential mold and leaks that's the reason for such limitations. A letter to the Board of Directors c/o your Property Manager asking for their permission/clearance is the right thing to do in this case.

[patman]

Not sure on your weight calculations. 1 gallon of water is like 10 lbs. Your 60" tank sounds like about 130 gallons so about 1300 lbs just for the display tank water. I know there isn't that much water as rocks and substrate displace it, but they also add to the weight. Then add in the tank weight, sump, equipment, ..... My place was rated for only 75lbs/ft so I ended up re-enforcing the floor between the joists to spread out the weight. Best if you can do it near a load bearing wall.

[Ryan]

You guys forget the floor isnt just going to give out. Your going to see the flex slowly before it gives way.

[Harpo]

So what was the outcome???