Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > DIY

Reply
 
Thread Tools Display Modes
  #1  
Old 02-15-2011, 03:37 AM
eli@fijireefrock.com's Avatar
eli@fijireefrock.com eli@fijireefrock.com is offline
Vendor
 
Join Date: Jan 2002
Location: calgary
Posts: 1,758
eli@fijireefrock.com is on a distinguished road
Default

if you did it in such a small ratio of cement.
i would break a rock in half and place it back in water and again test for ph.
of course after testing it for Phosphates.
good luck,hope all goes good.
Reply With Quote
  #2  
Old 02-15-2011, 04:49 AM
MicroTankin MicroTankin is offline
Member
 
Join Date: Mar 2010
Location: Airdrie, AB
Posts: 28
MicroTankin is on a distinguished road
Default

Ya I will test for phosphates, and I have tried breaking a rock and it did not change the ph so... I will give it one more week and then see how things go. It is going into its own tank and I am going to seed it...so I am not worried about it ruining a established system, thanks for the advice
__________________
Ben

-Sometimes I wonder who is looking at whom through that glass?-
Reply With Quote
  #3  
Old 02-15-2011, 06:42 AM
wolf_bluejay wolf_bluejay is offline
Member
 
Join Date: Nov 2007
Location: Kamloops, BC
Posts: 84
wolf_bluejay is on a distinguished road
Default try a bit of salt

when I did a bunch ages ago, I found that after the PH stabilized out in fresh water it would spike again in salt.
I would add some salt to the water (if you want to be cheap, just use rock salt) and watch the PH again. Mine spike up to 11 after adding in the salt, and took about 2-3 weeks to come down again.
Reply With Quote
  #4  
Old 02-15-2011, 07:01 AM
eli@fijireefrock.com's Avatar
eli@fijireefrock.com eli@fijireefrock.com is offline
Vendor
 
Join Date: Jan 2002
Location: calgary
Posts: 1,758
eli@fijireefrock.com is on a distinguished road
Default

Come to think of it, years ago i had the same problem as Wolf_bluejay.

Quote:
Originally Posted by wolf_bluejay View Post
when I did a bunch ages ago, I found that after the PH stabilized out in fresh water it would spike again in salt.
I would add some salt to the water (if you want to be cheap, just use rock salt) and watch the PH again. Mine spike up to 11 after adding in the salt, and took about 2-3 weeks to come down again.
Reply With Quote
  #5  
Old 02-16-2011, 02:58 AM
MicroTankin MicroTankin is offline
Member
 
Join Date: Mar 2010
Location: Airdrie, AB
Posts: 28
MicroTankin is on a distinguished road
Default

I did have them in salt about two weeks ago for about a week and no spike so I went back to freshwater curing. I am pretty sure they are cured because I have 2 batches curing in two seperate tanks and they have both been holding at 8 for weeks now....I am going to soak for one more week and start the tank up I think...see how it goes?
__________________
Ben

-Sometimes I wonder who is looking at whom through that glass?-
Reply With Quote
  #6  
Old 02-17-2011, 03:04 AM
Wayne's Avatar
Wayne Wayne is offline
Member
 
Join Date: May 2010
Location: Edmonton
Posts: 938
Wayne is on a distinguished road
Default

Sounds like you are ready to go. Seeding it in its own tank is going to be redundant but definatly a good idea!
Reply With Quote
  #7  
Old 02-17-2011, 04:29 AM
blacknife's Avatar
blacknife blacknife is offline
Member
 
Join Date: May 2009
Location: Leduc
Posts: 475
blacknife is on a distinguished road
Default

i tried putting some of my diy rock that i thought was stabilized in my nano. not much just a bigger piece or 2. I had a powerhead incident that blew half the water out of the tank and the heater really heated up the remaining water and the ph went through the roof. back in the bin went the rock.

I wonder if cooking up the heat on it would speed up the ph leaching
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 09:31 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.