![]() |
|
#1
|
|||||
|
|||||
![]() what do it take out NO3 and phosphates
__________________
180 starfire front, LPS, millipora Doesn't matter how much you have been reading until you take the plunge. You don't know as much as you think. |
#2
|
|||||
|
|||||
![]() Hey, they are pretty good, helps to create a NLS (nutrient low system) eating up all those nasty things like nitrates.
There is a trick to using them, keeping them tubmling vigorously on top, but very very slow at the bottom of the reactor. Also exporting the water from the reactor in front of the skimmer intake. If setup properly, they do a good job.
__________________
![]() Setup: 180G DT, 105G Refuge (approx. 300lbs LR, 150lbs Aragonite) Hardware: Super Reef Octopus SSS-3000, Tunze ATO, Mag 18 return, 2x MP40W, 2X Koralia 4's Wavemaker Lighting: 5ft Hamilton Belize Sun (2x250W MH, 2X80W T5HO) Type of Aquarium: mixed reef (SPS & LPS) with fish Dosing: Mg, Ca, Alk |
#3
|
|||||
|
|||||
![]() That is my other question where does everyone have the water output from there reactors? I know Rick has his going back in front of his skimmers, what about the rest of you?
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#4
|
|||||
|
|||||
![]() Output of reactor close to intake of skimmer. I believe this is typically recommended by the manufacturers, and makes sense. As the bacteria consumes pellets they too will generate waste and you typically want that waste exported via the skimmer. Of course, not all if the bacterial waste will get skimmed out. Some will escape back into the tank and will become food for corals and other filter feeders.
|
#5
|
|||||
|
|||||
![]() I have search for this info but have never been able to find it any where, maybe I was looking in the wrong place. My output hose is now down right in front of the pump that feeds my 1st skimmer.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#6
|
|||||
|
|||||
![]() I have a 400G system with 2 reactors.
1 x converted 3qt ZEOvit reactor with 1500 ml of pellets 1 x Vertex UF20 with 1100 ml of pellets The ZEOvit reactor drains just in front of my skimmer intake. The Vertex UF20 drains directly into my sump. Tom R |
#7
|
|||||
|
|||||
![]() Greg,
The reason for having the export from the pellets infront of the skimmer intake is for 2 reasons: 1.) The pellets do depleat the water of oxygen, so the skimmer re-oxygenizez the water 2.) To remove any excess that the pellets do create, anything not removed becomes food for the coral. I hope this helps.
__________________
![]() Setup: 180G DT, 105G Refuge (approx. 300lbs LR, 150lbs Aragonite) Hardware: Super Reef Octopus SSS-3000, Tunze ATO, Mag 18 return, 2x MP40W, 2X Koralia 4's Wavemaker Lighting: 5ft Hamilton Belize Sun (2x250W MH, 2X80W T5HO) Type of Aquarium: mixed reef (SPS & LPS) with fish Dosing: Mg, Ca, Alk |