pH too low questions...

PoonTang · #1 07-14-2010, 08:29 PM

did you calibrate your probe using both ph7 and 10 solutions?
are you running a ca reactor?
what is your Alk at?

Milad · #2 07-14-2010, 08:44 PM

I didnt calibrate my probe but it was new in a box with a end that had fluid in it already and the instructions didnt say anything about calibrating it, just said never let it out of water.

Im not running CA reactor yet (almost got it ready to put in though)

I just bought alk test kit so ill test tonight and see whats up.

untamed · #3 07-14-2010, 09:17 PM

You need to calibrate that pH probe before you do anything based upon what it says.

In addition, I think your plan to move your pH upward is dangerous. The additive you are looking at will alter your Ca/Alk balance by raising Alk. That is something that can cause a lot more problems than low pH.

Given you aren't running your Ca reactor yet, I suspect that you don't have a seriously low pH problem anyway.

Milad · #4 07-14-2010, 09:29 PM

well the calc reactor was about to go in this weekend but i heard they lower the ph because of all the co2 you gota pump into them. now im going to have to put that on the back burner.

Megalodon · #5 07-14-2010, 09:29 PM

If your kH and calcium balance is OK, I wouldn't worry as much about pH, as it really comes down to CO2 at that point. CO2 levels go up at night and thus the pH falls. I also noticed the deeper I place the pH probe, the lower the pH is, so keep that in mind.

As for using that buffer, it's not the best idea to use it until you know your alk and calcium levels. To a lesser extent also magnesium.

Since you're putting the calcium reactor on hold, instead of that pH buffer, I would actually recommend to you a two-part. Kent makes a decent one IMO. There's part A and part B, both in liquid forms, added to different parts of the tank, or at different times, always in equal amounts.

http://www.jlaquatics.com/product/k-...+-+64+oz..html

If low pH is still a concern, you could also drip limewater (kalk) at night and/or have a reverse lighting refuge with algae.

Milad · #6 07-14-2010, 09:34 PM

Quote:

Originally Posted by PoonTang

did you calibrate your probe using both ph7 and 10 solutions?
are you running a ca reactor?
what is your Alk at?

Quote:

Originally Posted by Megalodon

If your kH and calcium balance is OK, I wouldn't worry as much about pH, as it really comes down to CO2 at that point. CO2 levels go up at night and thus the pH falls. I also noticed the deeper I place the pH probe, the lower the pH is, so keep that in mind.

As for using that buffer, it's not the best idea to use it until you know your alk and calcium levels. To a lesser extent also magnesium.

Since you're putting the calcium reactor on hold, instead of that pH buffer, I would actually recommend to you a two-part. Kent makes a decent one IMO. There's part A and part B, both in liquid forms, added to different parts of the tank, or at different times, always in equal amounts. You could also consider dripping lime at night.

http://www.jlaquatics.com/product/k-...+-+64+oz..html

ill go return the ph buffer and try this two part and see what happens.

PoonTang · #7 07-14-2010, 09:49 PM

Yes i would suspect that it is just a calibration issue. Also how heavy is your sps load? you may not even need a Calcium reactor. You may want to concider dosing Kakwasser or 2 Part. If you go the Calcium reactor route you will want to get a second PH probe for your Apex.

Milad · #8 07-14-2010, 09:54 PM

Quote:

Originally Posted by PoonTang

Yes i would suspect that it is just a calibration issue. Also how heavy is your sps load? you may not even need a Calcium reactor. You may want to concider dosing Kakwasser or 2 Part. If you go the Calcium reactor route you will want to get a second PH probe for your Apex.

I Already have calc reactor and ph probe on it so its ready to go, just need to get a refill on cylinder and new solenoid.

my sps load isnt really heavy i dont think, one big (8" round) birds nest and a hand full of frags, maybe 5 or so.

PoonTang · #9 07-14-2010, 09:57 PM

Technically you could hold off on the reactor for now if you want. Those corals wont suck that much Ca out of 180G of water. Your regular water changes should look after it no problem and you can always "tweek" the levels as necessary with 2 part.

#10 07-15-2010, 08:32 AM

If your PH is 8 you are OK I found that my fish did not like it when my PH went down to 7.8 or lower I do use kalk KH buffer with mag in it to get extra CA in the tank and to raise the PH to between 8.1 and 8.2. I do not use reef buffer as it has to many things in it from what I've heard. I don't trust a product that does not list he ingredients on the label.

Bill