|
|
|
|
|
#1
04-14-2010, 04:23 AM
|
|||||
|
|||||
I wanted espresso finish but this one is the 'modern light' finish and I like it.
I've run AC 250 14k and it was an awesome bulb. Same quality in this wattage? I was going to run the Phoenix 250w in the SunPod since it's a good and cheap bulb and I wondered if the 150w version was also good. Both are good choices? I'll start slow with a few lps but this tank will eventually be mostly SPS if the lighting allows it. Last edited by lastlight; 04-14-2010 at 04:25 AM. 
|
|
#2
04-14-2010, 04:27 AM
|
|||||
|
|||||
|
I'm running a AC 150 14k over my 33g, I like it. I would compare it to my AC 400's 14k I have on my 150g.
__________________
Mike 150g reef, 55g sump, T5's, Vertech 200A, Profilux III - German made is highly over rated, should just say Gerpan made. Reefkeeper - individual obsessed with placing disturbing amounts of electricity and seawater in close proximity for the purpose of maintaining live coral reef organisms.
|
|
#3
04-14-2010, 04:32 AM
|
|||||
|
|||||
|
I ran The AC 150w's and had tons of growth and great color! I had mainly LPS and a few SPS in the top half of my 24" deep tank. I have never ran the Phoenix 150'9s tho and from what Ive read their 250 bulb is much better than the 150 bulb(according to RC threads)
__________________
60" 120G project-DONE!!!!
|
|
#4
04-14-2010, 04:54 AM
|
|||||
|
|||||
|
I was having troubles reading the label on the ballast which i mounted on the back of the tank. That is until I remembered I can swivel my disco ball to hang over the back of the tank!
Turns out this is an m81 ballast (hqi) so I'm going to try out the radium 20k (which runs best on hqi) which I read is very intense with not a ton of blue but nice coloration of the tank.
|
|
#7
04-21-2010, 05:57 AM
|
|||||
|
|||||
|
Still doing my freshwater test while I wait for the following to arrive (wait is KILLING ME):
Tunze 9002 Custom Collection cup to fit Solana Tunze Osmolator Tunze 6025 BRS 2-part Chems, RO/DI membrane 150w Radium 20k The done list: Wired up my new Ranco temp controller today (had sold old one along with my Osmolator when I shut down the last tank). There were a few extra steps/parts since I made a mistake and ordered the 24V (not 120V) version but it's keeping my tank temp perfectly now. Removed stock pump and have a dead silent (and cooler) MJ600 in there now. Added sand after a thorough rinsing. Sand is CaribSea and is a nice mix of finer grains with some coral/shell bits. Wired and attached moonlights. Not sure of the brand but there are 3 LEDS which are tie-wrapped to part of a black plastic coat hanger piece. This is in turn tie-wrapped to the pendant arm.    Guts of my stand not as clean and organized as my old one and i totally don't care =) I plan to frost the glass so my shameful pile of cords is hidden. Will have a small topoff reservoir on the bottom shelf...fancy tupperware or something.  Last edited by lastlight; 04-21-2010 at 05:59 AM.
|
|
#9
04-25-2010, 01:40 PM
|
||||
|
||||
|
[quote=lastlight;512300]Still doing my freshwater test while I wait for the following to arrive (wait is KILLING ME):
Brett, Honestly.... I think you are the most patient reefer out there.  Can't wait to see what fishy's you pick. 
|
|
#10
04-14-2010, 05:43 AM
|
|||||
|
|||||
|
Quote:
__________________
28g Nano Cube drilled with 13g sump in stock stand. Vertex IN80 Skimmer, Phosban 150 Reactor, Apex Controller, DIY LED with stock hood, dimmable Established March 2006
|
Hybrid Mode
