VERY custom tank builders in Calgary?

[calkrog]

have you checked out bow valley aquariums ? they will build whatever you want, but im sure golds will get it built any way you want aswell, you just have to be very specific in what you want?

[mseepman]

Theresa,

Aquarium Illusions out of Edmonton builds custom tanks to your spec. Also, Aquarium Obsessions out of Toronto does too. I know both seem far away but I've got a quote from both and it wasn't as bad as it sounds and I'm farther away than you. To put perspective on it, Aquarium Obsessed is like the Oceanic of customer tank builders...higher quality and very good ratings. Aquarium Illusions is like the All Glass builders...very good quality and nice decent ratings.
I've also heard that Albert is an excellent resource for getting anything you want and he's helped me any time I've been into Golds. I just don't know who builds their tanks for them.

Here is a thread that you might want to follow along with as it is close to what I plan to get and similar to what you're looking for.
http://www.canreef.com/vbulletin/showthread.php?t=37962

Again, this is all just my opinion from the research I've done, but I can tell you that the knowlegeable people on here will really help you out.

Mark.

[Der_Iron_Chef]

I'm pretty sure Gold can build you that tank. You should ask specifically (it sounds like you didn't before).

[Delphinus]

Acrylic over glass overflows is quite common actually. Although usually for glass overflows, instead of teeth, you usually see black eggcrate. This might be slightly advantageous because eggcrate is easily replaced whereas a broken overflow tooth might not be as easily redone.

My 280g was built by Bow Valley, although it was 3 years ago. I'm aware of their reputation but they were fine for me and based on my experience alone I'd have no reason not to go back and have another built. That said, I know the tanks that Albert & Dennis build are fine too.

Just be firm with what you want when you speak to a builder ... it helps to have drawings. I found there were a couple of things I wasn't that firm on and I got talked out of doing (for the sake of a lower cost) but in the end I kind of wish I had insisted on - the problem was I didn't really know what I want so I kind of let the builder steer me on a couple issues. Looking back, now that I have the tank in the spot I want it there are things I wish I had done differently (eg. overflow in particular). Oh well, it is what it is, I'll live with it since the alternative is .. well .. not practical. So my best advice is plan this as detailed as you can, do some drawings and say "This is what I want. Make it so!"


PS. Welcome to Canreef!

[wickedfrags]

Depite my bad experience with them, you should also see who can get uou a quote on a Miracles tank. Historically they build great tanks and can include any feature you can think of.

[mccrat]

I do have pretty detailed drawings and yes have found that some just like to do it 'Their' way and are very opinionated. I have some good resources now and hopefully will find someone to build it the way I want. Here is a link to Brian's build thread on reefcentral. It is very similar to what I want. When I start my build I will start a build thread here for you all. Thanks so much!

http://www.reefcentral.com/forums/sh...5&pagenumber=1

Theresa

[albert_dao]

Originally Posted by mccrat

I do have pretty detailed drawings and yes have found that some just like to do it 'Their' way and are very opinionated. I have some good resources now and hopefully will find someone to build it the way I want. Here is a link to Brian's build thread on reefcentral. It is very similar to what I want. When I start my build I will start a build thread here for you all. Thanks so much!

http://www.reefcentral.com/forums/sh...5&pagenumber=1

Theresa

Not to sound like a snob or anything, but just because it looks good on paper doesn't mean it actually is.

eg. you realize that drilling the bottom of the tank is probably the worse thing you can do eh? The reason dude is gonna get away with it is because his bottom plate ISN'T glass, it's PVC. Also, buddy is using Durso's in his overflow box. From a design standpoint, Durso's are strictly inferior to Herbie's. His sump also mandates an external skimmer as it cannot maintain water level without constant attention or a level controlling monitor.

That said, what exactly was it that you wanted with this tank? Give me a call at the store (Gold Aquariums) if you want to discuss these custom features.

Edit:

http://canreef.com/vbulletin/showthr...t=36052&page=2

[wickedfrags]

Lets here more about your tank now

My display is 72"l x 26"w x 24" high - 12mm starphire on the three viewable sides. I do not use standpipes, and do not see the issue with drilling the bottom of a tank.

Originally Posted by mccrat

I do have pretty detailed drawings and yes have found that some just like to do it 'Their' way and are very opinionated. I have some good resources now and hopefully will find someone to build it the way I want. Here is a link to Brian's build thread on reefcentral. It is very similar to what I want. When I start my build I will start a build thread here for you all. Thanks so much!

http://www.reefcentral.com/forums/sh...5&pagenumber=1

Theresa

[Buccaneer]

Originally Posted by mccrat

I do have pretty detailed drawings and yes have found that some just like to do it 'Their' way and are very opinionated. I have some good resources now and hopefully will find someone to build it the way I want. Here is a link to Brian's build thread on reefcentral. It is very similar to what I want. When I start my build I will start a build thread here for you all. Thanks so much!

http://www.reefcentral.com/forums/sh...5&pagenumber=1

Theresa

Well that is a interesting idea to use a PVC base ... I do have a few thoughts that come to mind though ...

a closed loop is not a " necessity " especially coming up from the bottom like that ... so if a closed loop is something you want and the tank is 30" or less ( front to back ) then utilizing the sides or the back would be just as effective IMO ( I had a 330G for 6 years [96 X 24 X 33 ] with 2 closed loops on the back using eductors and it was very effective ) ... so the cost of a hybrid material build like that will likely be higher than a all glass tank ... is it worth it ?

The other thought is that closed loops themselves require pumps that draw alot of amps and until you have actually had the pleasure of paying those hydro bills on a regular basis you may want to consider another energy efficient source for circulation ( ie. the new powerheads that stick on the glass [ cant remember the name ] that use low amps but generate huge flow ) ... the advantage here is that they can be moved later on as your coral start to grow so that optimal circulation is achieved no matter how mature the tank ) ... when compareing the cost of a closed loop now versus the powerheads ( last time I looked they were a few bucks ) you need to include the extra cost of the tank if you go PVC + the pumps + extra hydro cost per month + ocean motion + plumbing etc etc

the latter comments are part of my thought process for my next tank build which will definately be this year ( 450G ) ... I may plumb the tank for a closed loop or 2 from the start ( in case later on more energy efficient pumps come along ) but likely will utilize the powerheads instead

which brings me to the tank builder

Bow Valley are not trustworthy ... you can do a search here or on RC and you will get LOTS of hits on the subject ... if it looks like a rat, smells like a rat ... then likely it IS a RAT ( you can do a search under my name here for my experience with Bow Valley as well )

IF you decide to go all glass ( my recommendation ... acrylic scratches too easy and not sure if you can get that PVC combo here in Calgary for a practical price ) then the tank builder I would recommend locally would be Golds ... Albert and Dennis are very good to deal with ( opinions aside ) and they deliver what they promise for the price they promised - they built a tank for a friend of mine and it turned out exactly as specified

[hurley]

bow valley builds nice tanks at a good price, ive got a couple built and im always happy with the result