How to stop Sump Drain Gurgle?

Twisted-1 · #1 10-08-2006, 02:10 AM

How can I get my tanks drain line to the sump to stop gurgling. I can get it quite by really downing the flow but thats no good. Is there a way to route the piping in the overflow to get rid of this noise?

Coderad · #2 10-08-2006, 02:59 AM

Pm sent

niloc16 · #3 10-08-2006, 03:07 AM

i'm interested to hear how as well, i'm having the same issue

RicePaddy · #4 10-08-2006, 04:07 AM

Did "O"

Palster · #5 10-08-2006, 04:21 AM

One of the most effective ways to stop the gurgling sound is to build a Durso Stand Pipe. Here is the link http://www.dursostandpipes.com/ You can click on the build your own standpipe tab or if you don't want to build one yourself I believe you can order one through the web site as well.

niloc16 · #6 10-08-2006, 04:38 AM

i currently use durso's but the noise comes from the water entering the sump is burping and gurgling

Tarolisol · #7 10-08-2006, 05:54 AM

If your pipe goes into the water then you will get gurgiling, you should raise it to just above the water line, and if thats to loud then angle the pipe entering the sump if you can to give it a little slop.

fkshiu · #8 10-08-2006, 06:21 AM

If you've got an overflow with 2 bottom drains (e.g. AGA Megaflow), there's the "Herbie" method from RC. It's essentially 2 vertical standpipes in the overflow, one taller than the other. The shorter standpipe flows down into the sump through a gate valve which is adjusted so that the overflow water level is at a height between the shorter and taller standpipes. Don't have the link with me now, but by all accounts it's dead silent.

If that's not possible, I've seen people put a Stockman standpipe on the final downward elbow before the water hits the sump.

The gurgling/splashing is caused by the air that's introduced from the overflow. A Durso, while silencing the overflow, can actually make the gurgling at the sump worse because of the additional air it introduces up top.

The Herbie method is silent because there is no air introduced in the first place. Water merely falls down by gravity. The Stockman just before the sump method works because the air added up top gets flushed out by the Stockman just prior to hitting the sump.

Matt · #9 10-08-2006, 04:13 PM

I've taken a slightly low-tech approach, which was to cut a 2l pop bottle so that the down-flow was just barely underwater, and it overflows back up and over the side. I cut one side a little lower to allow the water to exit smoothly, and it got very quiet. I can make it almost silent, but I have to let the water make some noise, though, or I get frustrated by the sounds of fans and pumps, and I like water noise better than machine noise. As an added bonus, it brings all the bubbles back to the surface before they enter the sump.

GMGQ · #10 10-09-2006, 06:57 AM

I use the herbie method. It works Beautifully.

I use it in my overflow box.

So on that drain where the rolled up gutterguard is, at the bottom, there is a gate valve that chokes back the flow until there is no gurgling. The gurgling is from the drain sucking down air. Once it's choked back, it's more like a syphon with no air sucked down. Therefore, no noise!

Quote:

Originally Posted by fkshiu

If you've got an overflow with 2 bottom drains (e.g. AGA Megaflow), there's the "Herbie" method from RC. It's essentially 2 vertical standpipes in the overflow, one taller than the other. The shorter standpipe flows down into the sump through a gate valve which is adjusted so that the overflow water level is at a height between the shorter and taller standpipes. Don't have the link with me now, but by all accounts it's dead silent.