Euro Brace SUMPS in-stock

[Reef Supplies]

Hi Everyone

We just received our first shipment of incredibly well built sumps! The are made in the USA by Trigger Systems and are very well priced.

Features

- "Euro bracing" for added strength
- Beveled edges
- Made in the USA

30" Standard Sump

http://www.reefsupplies.ca/online-st...dard-Sump.html



Dimensions: 30" long x 12" wide x 15" high
Drain/Skimmer Section: 11" x 11.5"
Center/Refugium Section: 9.5" x 11.5"
Return Pump Section: 6" x 11.5"

-----

36" Standard Sump

http://www.reefsupplies.ca/online-st...dard-Sump.html



Dimensions: 36" long x 14" wide x 15" high
Drain/Skimmer Section: 12" x 13.5"
Center/Refugium Section: 12.25" x 13.5"
Return Pump Section: 8" x 13.5"

------

30" Elite Sump

http://www.reefsupplies.ca/online-st...lite-Sump.html



Dimensions: 30" long x 16" wide x 15" high
Drain/Skimmer Section: 15.5" x 11"
Refugium Section: 18.25" x 7.625"
Return Pump Section: 15" x 7.625"

-------

36" Elite Sump

http://www.reefsupplies.ca/online-st...lite-Sump.html



Dimensions: 36" long x 16" wide x 15" high
Drain/Skimmer Section: 15.5" x 12.5"
Refugium Section: 22.75" x 7.625"
Return Pump Section: 19.5" x 7.625"

----

18" Cube Sump

http://www.reefsupplies.ca/online-st...Cube-Sump.html



18x18x18"

---

Standard Flow



Section 1 is typically where the protein skimmer sits. Then the water flows through a slit in the first baffle into Section 2.

Section 2 is typically used as a refugium. If a refugium is not desired then the protein skimmer or other equipment can be housed here. The water then flows over the second baffle through 2 perforated platforms and under the third baffle into Section 3. The top perforated baffle comes with a foam block filter and the bottom one is open to use for several different filtration methods (bag of carbon, bio balls, rubble rock, etc.).

Section 3 is the return water section back into the tank. This is where the return pump will sit.

----

Elite Flow



Section 1 of the ELITE diagram above is the refugium section. The flow rate through the refugium can be controlled based on the type of algae that is housed there. There are several ways to feed water into the refugium.

Split or use one of the drain lines from the tank
Tee off from the return pump
Use a small pump that sits inside the sump

If splitting off one of the drains from the tank is the method chosen, then it is recommended to put valves on both lines after the split to control flow. Water flows from the refugium into Secton 2.

Section 2 is where the water from the main tank enters through the filter socks. This is the section where the protein skimmer typically sits. Water from this section goes over a baffle and through a foam block filter which is provided and then under a baffle into Section 3.

Section 3 is the return water section back into the tank. This is where the return pump will sit.

----

Please let us know if you have any questions

thanks
Ray

P.S wholesale welcome through www.ReefDealer.ca

[Bugger]

These dont come with the ruby red euro bracing do they have the probe holders. Why dident you get these five months ago

[Reef Supplies]

Hey

These are not the ruby series and nope, no problem holders. We chose the standard and elite because we felt these were the best bang for the buck. They are really nice, pictures don't do them justice.

Ray