|
|
|
#191
05-09-2012, 05:12 AM
|
||||
|
||||
Love that skimmer
__________________
150DD mix reef with 90 gal sump and 40gal frag tank purple tang, sohal tang, yellow eye kole tang, fairy wrasse. cleaner wrasse, leopard wrasse, and misc fish. GHL Mitras 6200HV X 2, MP40 X 2, MP60 X 1, tunze 6095 X 2, Vertex RX6 calcium reactor, Bubble King SM250, Aquamaxx bio pellets reactor, Profilux 3 
|
|
#192
05-09-2012, 05:29 AM
|
|||||
|
|||||
|
Quote:
I'm just learning how to use it
|
|
#193
05-09-2012, 05:31 AM
|
|||||
|
|||||
|
This is not the scaping plan
Just evidence that the LR is finally in  
|
|
#195
05-09-2012, 06:03 AM
|
|||||
|
|||||
|
Quote:
LR cured for 3 months in the dark I lost all the mini brittle stars, don't see the mini hermit and don't see any amphipods anymore Still have a couple mini clams and a small snail Can't wait to add stuff !! SG 1.026 pH 8.14 NO3 0.00 +/- PO4 0.00 +/- No other testing yet ... no point 
|
|
#196
05-11-2012, 08:46 AM
|
|||||
|
|||||
|
I finally got around to setting up this Tunze ATO 3155
I gotta tell ya, when I first walked away from it, I thought it was all good. I tested it by pulling water out with a jug, and then putting it back, and all was great. I went to the kitchen and started a conversation with the wife .... Not long after, the Hi alarm went off and we thought it was something on the TV  I ran to the sump room and, after viewing the problem, I unplugged the power supply to the ATO. It had already dumped 1 gallon of RO into the sump !!!!!!!!! I then spent the next, say, 2 hours, setting it up and I think it's all good now. So, problem solved, at least overnight, and we'll deal with it tomorrow I had to add some salt and remove some water ...... My problem, I think, was the chaeto tank. For those of you that haven't been following along, it's above the sump on a separate pump. I watched when the chaeto tank level raised, and, of course, the sump level dropped. I never thought this would be enough to upset the ATO, but it did. The trick was to set the ATO to ignore all this, yet still work properly I ended up having to set the Optical sensor much higher than originally planned. It is now very close to the HI level float. Seems to work so far ... 3 hrs running and no stupid cycling I cannot post a good pic as the location of the mounts is tight Useless pic .....  Last edited by gregzz4; 05-11-2012 at 08:49 AM.
|
|
#197
05-13-2012, 12:55 AM
|
|||||
|
|||||
|
The Tunze ATO started acting up
It has been giving me the 'wet internals' alarm There's no way it got wet, but I took it apart anyway to ensure there's no moisture inside it. None. So, I've done 2 things hoping to solve this issue; First, the ball valve from the chaeto tank was not sensitive enough to get the drain level perfect. It was sucking air intermittently, filling the sump with bubbles. Possibly those bubbles were upsetting the optics The ball valve was just replaced with a gate valve I've gone from this ( blue valve )  To this  The other thing I've done is move a relay away from the Tunze Controller, just in case an electrical or magnetic field was the issue From this  To this  Only time will tell now if it's resolved
|
|
#199
05-13-2012, 01:09 AM
|
|||||
|
|||||
|
Lol, ya think ?
Seriously though, the ATO warning was going off a couple times a day It don't work so well in that mode 
|
|
#200
05-13-2012, 01:22 AM
|
|||||
|
|||||
|
ATO tank pic
I may unplug the heater - haven't decided yet Looks like I'm using about 1g/day, so I'll get 8 days before the pump is shut off The upper float kills both the powerhead and heater, and the lower kills the ATO pump The relays in the previous pics are for these 2 floats 
|
Linear Mode
