Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Product Review and Equipment Forum

Reply
 
Thread Tools Display Modes
  #1  
Old 01-13-2014, 10:42 PM
Madreefer's Avatar
Madreefer Madreefer is offline
Member
 
Join Date: Nov 2008
Location: Prince George
Posts: 2,064
Madreefer is on a distinguished road
Default Carbon and GFO Together?

I'm getting a muck bigger reactor than the 2 TLF reactors I use now. So can I combine both the carbon and GFO together in one reactor and is there anything that I may be encountering while doing this? Thanks
Reply With Quote
  #2  
Old 01-13-2014, 10:53 PM
Werbo Werbo is offline
Member
 
Join Date: Oct 2003
Location: Victoria, BC
Posts: 436
Werbo is on a distinguished road
Default

Yes and no. For example. Boyd's Chemipure Elite has both GFO and carbon but it is in the mesh bag so the GFO never churns.

You can but you will not get maximum effeciency from the GFO. GFO should be slightly churning or boiling. GFO is much harder than carbon. If your GFO is churning/boiling then it will grind the carbon to dust.
Reply With Quote
  #3  
Old 01-14-2014, 12:09 AM
Madreefer's Avatar
Madreefer Madreefer is offline
Member
 
Join Date: Nov 2008
Location: Prince George
Posts: 2,064
Madreefer is on a distinguished road
Default

But is anybody running a reactor with the 2 together and have you found a way to make it work?
Reply With Quote
  #4  
Old 01-14-2014, 12:35 AM
reefwars reefwars is offline
R.I.P.
 
Join Date: Apr 2010
Location: Calgary, AB
Posts: 6,186
reefwars will become famous soon enough
Default

Quote:
Originally Posted by Madreefer View Post
But is anybody running a reactor with the 2 together and have you found a way to make it work?
you can run in a daisy chain fasion , and you can mix them you just dont maximize the use out of each , as stated the tumbling speed of each is diff , with gfo your looking to pass as little water through while keeping a gentle boil , carbon can handle much more flow than gfo can as gfo is very soft

mixing the two works fine but isnt ideal
__________________
........
Reply With Quote
  #5  
Old 01-14-2014, 02:39 AM
The Guy The Guy is offline
busy with fresh water.
 
Join Date: Dec 2011
Location: Kelowna, BC
Posts: 1,041
The Guy is on a distinguished road
Default

Quote:
Originally Posted by Madreefer View Post
I'm getting a muck bigger reactor than the 2 TLF reactors I use now. So can I combine both the carbon and GFO together in one reactor and is there anything that I may be encountering while doing this? Thanks
Hey Bill have look at the BRS site they got good video's on running both together, pro's & con's
__________________
Hey! I never "LEFT" the hobby, just doing fresh water now. Which is still listed as part of Canreef if I'm not mistaken.
Reply With Quote
  #6  
Old 01-14-2014, 02:48 AM
Werbo Werbo is offline
Member
 
Join Date: Oct 2003
Location: Victoria, BC
Posts: 436
Werbo is on a distinguished road
Default

Quote:
Originally Posted by reefwars View Post
carbon can handle much more flow than gfo can as gfo is very soft
You have that backwards. GFO is denser and harder than carbon. GFO can be tumbled at a slow boil. If you tumble carbon it will disintegrate in a short time.
Reply With Quote
  #7  
Old 01-14-2014, 02:57 AM
Zoaelite's Avatar
Zoaelite Zoaelite is offline
Member
 
Join Date: May 2007
Location: Calgary
Posts: 2,461
Zoaelite is on a distinguished road
Default

In addition to the harder material crushing the softer material they have different refresh rates.

Not sure about everyone else but my GFO gets replaced at the 2-3 month mark while my carbon is monthly.

You will be throwing out a ton of GFO which happens to be more expensive than the carbon so In my opinion I would keep it to 2 reactors.
Reply With Quote
  #8  
Old 01-14-2014, 04:27 AM
The Guy The Guy is offline
busy with fresh water.
 
Join Date: Dec 2011
Location: Kelowna, BC
Posts: 1,041
The Guy is on a distinguished road
Default

Quote:
Originally Posted by Zoaelite View Post
In addition to the harder material crushing the softer material they have different refresh rates.

Not sure about everyone else but my GFO gets replaced at the 2-3 month mark while my carbon is monthly.

You will be throwing out a ton of GFO which happens to be more expensive than the carbon so In my opinion I would keep it to 2 reactors.
+1 I run 2 reactors as well.
__________________
Hey! I never "LEFT" the hobby, just doing fresh water now. Which is still listed as part of Canreef if I'm not mistaken.
Reply With Quote
  #9  
Old 01-14-2014, 04:44 AM
SeaHorse_Fanatic SeaHorse_Fanatic is offline
Gold Member
 
Join Date: Oct 2004
Location: Burnaby
Posts: 4,880
SeaHorse_Fanatic will become famous soon enough
Default

I would daisy chain one of the Phosban reactors to the new bigger reactor. Keep them separate and so you can change out the carbon monthly and the GFO every 3 months or so.
Reply With Quote
  #10  
Old 01-14-2014, 10:31 AM
Madreefer's Avatar
Madreefer Madreefer is offline
Member
 
Join Date: Nov 2008
Location: Prince George
Posts: 2,064
Madreefer is on a distinguished road
Default

Well thanks guys! Looks like I'll have to buy another reactor to match the new one.
Change GFO every 2-3 months? I change both of them at the same time which is monthly, just a schedule i've put myself on. I've had a Hanna Phosphate checker since September, it's still in the box. I guess it's time I should start using it.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 11:19 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.