|
#1
|
|||||
|
|||||
How's your livestock, looking good? If so then there is no problem other than you chasing numbers measuring voltage in your tank water. Voltage up to about 40 is unlikely to give you a shock or harm you or your livestock. Anything metal in your water has the potential to introduce a measurable voltage. Even lights may induce voltage in the water, fluorescents being the most likely due to the electromagnetic field produced by the tubes.
Grounding the tank may not only mask the 'problem' but also make it worse, turning the static voltage you are measuring into current flowing to the ground probe. The only thing with an electrical cord in my tank are heaters and a small pump delivering water to my skimmer. If I need to know my pH, I use a test kit. Water movement is by EcoTech pumps with electric cord outside. I don't use a controller, so can't really advise on what may be up with your Profilux.
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206 Last edited by mike31154; 08-09-2017 at 03:44 PM. |
#2
|
|||||
|
|||||
What would be causing it? Perhaps everything
Could be "Magnetic induction" Had noticed the same issue in 2014 and discussed it HERE. Gets complicated. I no longer test for stray voltage, probably should but still don't know what to do about it |
#3
|
||||
|
||||
Quote:
I don't think the voltage is enough to harm anything but I need that ph probe to stay calibrated and working properly to control my calcium reactor. I'm not sure if it's because the controller plug in only has 2 prongs but from the googling I've done it looks like that's the right plug in. Another strange thing I noticed is when I hook up my laptop to the controller while everything was plugged in, the voltage dropped to 2 volts. That was with the laptop charger plugged into the laptop. If I unplug the laptop charger it's jumps back up to 20. Could it be because the laptop being connected to the controller has a 3 prong plug in and takes the voltage from the controller? |
#4
|
||||
|
||||
I pulled the controller off the tank and tested it in a pale of fresh salt water away from the tank and using different plug ins. when nothing is connected to the water it reads 2.5 volts. when i hook up the controller with only the temp probe it reads 3 volts. When i hook up the ph probe it jumps to 55 volts.
I also tried the ph probe on the conductivity and redox plug ins and still got 55 volts. maybe its time to switch to apex |
#5
|
|||||
|
|||||
Three prong plugs are generally used on higher power equipment such as drills & tools of that nature, especially if they have a metal case. It's a safety measure to protect you from shock if the case of the appliance is somehow shorted to the power lead. A GFCI device will also protect you in a similar manner, even if the equipment only has two prongs. Your aquarium equipment should all be connected through a GFCI. It's code these days for any circuit in a damp area or dealing with water.
Salt water is actually a mild electrolyte, i.e. similar to battery acid. If you have two metal objects in close proximity in a salt water solution, there is a potential for electricity to be produced, voltage & current. Your pH probe is metal..... Don't stress out too much. I understand you need the pH probe to work with your controller, but at the end of the day, many folks are quite successful running their tanks with fewer bells & whistles. Voltage itself poses no danger until it is given a path to create current flow, such as your hand in the water & bare foot in a puddle of water. The voltage would need to be quite high to complete that circuit through your body & zap you. In the tank it's unlikely any electrical current is flowing especially if you can put your hand in the water & don't feel a tingle or shock.
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206 Last edited by mike31154; 08-11-2017 at 03:18 PM. |
#6
|
||||
|
||||
Thanks for the help everyone. Since pulling off the controller I have only been getting 4-6 volts which is low enough for me. I do like the comfort of a controller so I'll be looking into buying a new one.
Thanks |
#7
|
||||
|
||||
What do you use to measure voltage in the water? What kind of meter?
|
#8
|
||||
|
||||
Quote:
I did noticed today that the plug in for the controller is only 2 prongs so (no ground?) Could that be the reason the ph probe is making the voltage jump? |