|
|
|
||||||||
| Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
10-10-2010, 04:29 PM
|
|||||
|
|||||
I read The Book of Coral Propagation by Anthony Calfo, The Reef Aquarium Vol 1 and 2 by Delbeek and Sprung, all of the articles on the subject on Reefkeeping.com and I hang out in the Coral Propagation and Aquaculture forum on RC a lot. I've also found a lot of good videos on youtube.com and elsewhere on the web. This isn't one of them... but I just have to post it again http://www.youtube.com/watch?v=jgbH04g6mXs
__________________
"We shall dive down through black abysses... and in that lair of the Deep Ones we shall dwell amidst wonder and glory forever." - H.P. Lovecraft Old 120gal Tank Journal New 225gal Tank Journal May 2010 TOTM The 10th Annual Prince George Reef Tank Tour 
|
|
#2
10-10-2010, 06:41 PM
|
|||||
|
|||||
|
I thought that it couldn't be that hard, so i learned the hard way, i used to use big chunks of Tunze reef epoxy, it would get smeared all over the frags, out of ten, maybe five would look good, the other five would have dead spots from where I had handled them with the epoxy on my fingers. LOL
Then I saw some frags with clear glue, so i bought the stony prop kit from J+L. It had some clear glue and accelerator, Way better results, less than 10% death rate. Now I use the ViaAqua plastic plugs, and the Zeo Vit reef cement. Most of the time i have zero casualties, no dead spots, and no weird chemicals like the accelerator. Rather than using a tile saw, I like the old hand saw, hammer and chisel technique, i did this for a bunch of encrusting monti's and some brains as well. I found that it gives the frag a more realistic appearance rather than having square chunks of coral mounted to plugs. After i had done all of these methods, my friend bought me the Coral Propagation book by anthony Calfo for my B-day. Absolutely the best book for learning how to frag, i wish i had stumbled across this earlier. Fun to read and not so much of the scientific terminology.
__________________
 90 gal SPS display+65 gallon mixed reef GEAR: Korallin calcium reactor, bio pellets, digital aquatics controller, Tunze ATO, MP40, 4 x Tunze 6105 w/controller, Reef Octopus Xp3000 ext, 2x250w MH, Futura LED.
|
|
#3
10-11-2010, 01:47 AM
|
|||||
|
|||||
|
It all started when I was cleaning the inside glass. Within a very short period of time I was fragging my corals.
Tom R
|
|
#4
10-11-2010, 02:13 AM
|
|||||
|
|||||
|
Quote:
__________________
360 gallon sps reef, 180 gal sump, bubble king supermarine 300, 4xmp40Wes, 2 x 6215 tunze waveboxes, 4 ghl mitras 360 Reef Tank
|
|
#5
10-11-2010, 03:44 PM
|
|||||
|
|||||
|
One_Devided taught me how to frag caps when we were helping Aquattro move his old tank. real fast method, but gets your foot wet....
Steve
__________________
 *everything said above is just my opinion, and may or may not reflect the views of this BBS, its Operators, and its Members. If cornered on any “opinion” I post I will totally deny having ever said this in a Court of Law…Unless I am the right one*Some strive to be perfect.... I just strive.
|
|
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
