Joe's Starfire 210

[plutoniumJoe]

I couldn't rip up the old floor due to the asbestos. Since I had a sub floor in place I wanted to nail the new floor instead of float. Without going to a true engineered wood I found a bamboo floor that I liked the look of and was suitable for below grade installation.



I know this is more of a basement build than a tank build but I am getting there. Trying to build the excitement.

Joe.

[plutoniumJoe]

When I cut away the floor for the tank I was surprised to find either a drain or a clean out.



I am thinking that this corresponds to the drain on the other side of the wall. If it is just the cleanout would it be possible to use it as a drain. I don't know where it would vent to, there was nothing in the wall. There is a bit of concrete on it that I could chip away at.

Any advice would be helpful.


Joe.

[sphelps]

I wouldn't open that, best to run a line to the drain on the other side of the wall.

Floor looks nice btw, don't know if you thought off this but it might be a good idea to mark the old floor as asbestos so that any future renovations by other people will know. I'm don't know about residential but any parts in commercial property containing asbestos has to be marked.

[plutoniumJoe]

Originally Posted by sphelps

I wouldn't open that, best to run a line to the drain on the other side of the wall.

Floor looks nice btw, don't know if you thought off this but it might be a good idea to mark the old floor as asbestos so that any future renovations by other people will know. I'm don't know about residential but any parts in commercial property containing asbestos has to be marked.

Thanks for the input. If I have to go that way I was thinking of just branching off the closed loop and draining to the other side for water changes.

I will try to make a marking somewhere, but the floor is down and nailed. I was thinking of putting a label under the base board as it will have to be removed before they tear up any floor. Hopefully people would test, the sign will save them $50 and a week delay.

[plutoniumJoe]

I want to be able to keep everything "fishy" under the tank, including an area for electrical. As the tank is 6ft I figure a 3ft sump would suffice and still give me enough room otherwise.

I got the glass cut for a 36X18X18 so potential for 50gallons. Of course when I got the glass cut the first time I forgot to take into account the thickness of the glass itself, so my sides were about 3/4" to wide. After a few practice tries I tried cutting 1" off the sides. The first one went well and straight, the second was good but a bit like a country road. I took out the old belt sander did what I could to clean it up. I siliconed everything together and it was pretty good, the slight curve of the cut made the side piece pivot at about the 1/3 mark on the way up. As I was making final adjustments the top or the bottom would pull away leaving some air bubbles in the silicone. Being a wood worker and having plenty of bar claps I simply clamped the bottom then applied some pressure to the top and things looked better. Of course a second clamp at the top would make things look better still. A couple gentle twists and all air bubbles were out. I sat back and admired my work and about 30 seconds later pop. The long piece broke. Back to the glass shop and attempt #2 but this time I had new sides cut as well.

I cleaned all the old glass with razor blades and a wire wheel. Once things were clean I dry fitted, re-taped and glued it up. I didn't end up using the corner clamps, got a good deal for 4 at LeeValley but I am happy with the GE 1200.
I just used duct tape to pull it together and it held. Seams were good with almost no bubbles.
I let the tank sit for about 3 days and it looked like there was a small bubble that formed about half way up one side. I did a leak test and the bubble grew until I realized it wasn't a bubble in the seam but a fault or fracture in the glass. A small dime sized portion of the class popped off. I thought for sure the tank would blow again but it held. Left water in for about 2 weeks and everything A-Ok. So I am not sure what to do from here. I crazy glued the piece back in, but I know structurally that does nothing. I was thinking of siliconing one of the small 1" strips over top just to give it some added strength. The water line won't go up to the point but I don't want a weak sump.

[sphelps]

The chip could spread into a crack down the road, best to replace the pane. It sucks but better to fix it now than find a flood later.

[plutoniumJoe]

I know the chip could spread but it is round in shape as opposed to sharp if that makes sense. I know that the extra few bucks to replace the pane of glass is better than replacing the new floor.
This picture is from the long side.



and this is from the end.