390 gallon installation

[muck]

BooYah!! That sounds awesome!!!

[TheReefGeek]

Where in the home is the tank going?

Are there any steps? Turns?

Obviously it is going to have to go on its side to go through doorways, and turning ability is going to be limited. De-glazing large front windows also provides access to your home if they are large enough.

You will probably want to use flat furniture movers, the ones that are basically a square board with 4 wheels covered in carpet. This way you can wheel it around instead of carrying.

You might want to look into glass suction cups if you need to grip the tank and a corner/edge is not useable. They basically suction to the glass, and have a handle for you to hold. Make sure they are meant for that kind of weight though, a window company might be willing lend you a pair for a night, or a weekend.

Other than that have lots of people, and ropes, straps, beer, etc.

Post some more details and we can help more.

[TheReefGeek]

Hmmmm, glass suction cups on acrylic, don't know if that works or not???

Other things to think about would be leveling the stand before putting the tank on it, and adding a layer of insulation foam between the stand and tank.

[untamed]

Good thoughts...all.

Yes, the tank will be moving on it's side. There's no turns. There's a choice of using a straight, exterior stairway...or a hill with bad (gravel) footing. It's possible that the tank could actually toboggan down the gravel with straps holding it back...

If we take the gravel hill, there isn't even any doors to go through!

The stand is mostly done, but I've not put any foam on it. Why do you think that foam is needed? I mean...it's flat. Putting foam on it isn't going to make it any more flat.

I'm thinking that a few of those suction cups would be helpful. To use them, I would need to strip off the protective covering on the spots where we would want to suck. I think they would work equally well on acrylic, but I'll check that out.

[Chin_Lee]

Originally Posted by untamed

Good thoughts...all.

Yes, the tank will be moving on it's side. There's no turns. There's a choice of using a straight, exterior stairway...or a hill with bad (gravel) footing. It's possible that the tank could actually toboggan down the gravel with straps holding it back...

If we take the gravel hill, there isn't even any doors to go through!

The stand is mostly done, but I've not put any foam on it. Why do you think that foam is needed? I mean...it's flat. Putting foam on it isn't going to make it any more flat.

I'm thinking that a few of those suction cups would be helpful. To use them, I would need to strip off the protective covering on the spots where we would want to suck. I think they would work equally well on acrylic, but I'll check that out.

Foam will eliminate any uneveness of your stand and reducing stress points as a result of the uneveness.post more info as time approaches. I will help out in anyway I can.

[GMGQ]

I concur with what Chin said. It also prevents tiny pebbles or specs of anything hard from putting stress on a single point of the bottom of your tank.

Imagine the weight of your tank , and a tiny piece of gravel under it somewhere :S

Better safe than sorry with like a 1/2" sheet of foam buffering it.

Originally Posted by Chin_Lee

Foam will eliminate any uneveness of your stand and reducing stress points as a result of the uneveness.post more info as time approaches. I will help out in anyway I can.

[Pansy-Paws]

I moved a 440 lb acrylic tank in two stages.

First, it came into the house using 6 people, and no suction cups. It was dicey keeping a good grip on the bottom, but was manageable.

The tank then sat for a month on our pool table until the stand was ready. The final move came with 4 people each using a suction cup. The tank felt about half the weight of the initial move, and was a breeze to lift onto the stand (at 45.5" tall).

Yes, you'll have to remove the paper coating on the acrylic to get a solid grip. I borrowed some suction cups from a professional firm, so they had ample capacity for the required lift (pump-action suction, not a lever setting). When I practized with a suction cup to check it out, I found that my strength gave out while lifting at an end of the tank before there was any sign that the suction cup was even thinking about slipping.

Definately required for the safety of all concerned ...

Good luck with that monster tank

[TheReefGeek]

Hmmmm, do they have "off road" furniture dollies?

The foam is to spread out the weight evenly and irregularities have less of a chance of causing your tank to crack. What is your stand made of? Could it warp 5 years down the road? It doesn't cost much, it is usually in pink or blue sheets at the hardware store, for the price I would use it for peace of mind.

[untamed]

The stand is wood...2x4s, 2x6s and 3/4" plywood...nothing too fancy. I suppose there is a chance that it could warp over time....but under 4000lbs of weight, I think any warpage forces couldn't overcome the force straight down.

I suppose it isn't a big deal...it's just 1/2" of additional height that wasn't in the plan. I'll look at it.

Does the foam compress at all under the weight of a tank?

[TheReefGeek]

Yes it does, how much depends on whether your tank supports everywhere, or just on the edges.