Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Tips and Tricks

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 05-05-2008, 01:22 AM
Myka's Avatar
Myka Myka is offline
Moderator
 
Join Date: Mar 2004
Location: Saskatoon, SK.
Posts: 11,268
Myka will become famous soon enough
Default Livestock Shipping How-To w/ Pics!

Ok, so it took me awhile, but here it is finally...

Alright, so maybe we only want to send a bag or two, and don't want to use one of those big and expensive to ship styrofoam fish boxes. So, we make our own!

Start with some 1" sheets of styrofoam. You can often find them for free if you go to places that sell appliances, office furniture or even cabinets and such as the sheets are part of the packaging. If you can't find any for free you can find some in building supply stores usually in the laminate floor section or rigid insulation section.






Cut it all up (I just use a steak knife) so that it lines the box tightly, including a lid.






Since a DIY styro box isn't water tight, Put a garbage bag in the box.




Add a layer of styrofoam packing peanuts.




Now it's time to bag up some critters! I double bag all bags, and put a layer of newspaper between the bags to prevent the critters from seeing eachother, or in the case of corals it prevents them from poking holes in the bag.

Start by getting a square piece of newspaper that is a couple inches bigger than the bag's width.




Fold it in half, and then on each end you fold it over so that it is just a tad smaller than the bag's width.




Put the folded newspaper into a bag, open it up, and put a second bag into the newspaper.




If you're shipping fish, just plop them in. If you fill the bag to the top of the newspaper you should be able to put up to a 4" fish in there ok...depending on the shape of the fish. A 4" wrasse sure, but not a 4" Tang. Fish ship better with oxygen in the bag instead of air, so it's a good idea if you have it available. Sometimes fish stores will allow you to use their oxygen.

If you're shipping corals, you need to prep them. If the coral is a branching type, or frags on a plug, then cut a disk out of the styrofoam sheet, poke a hole in the centre, and insert the frag plug or the stem. If it's possible use an elastic band to secure it. In the case of clams, brain corals, goniopora, non-branching euphyllia, bubble corals, etc that you can't attach to a disk, then just put them in the bottom with no disk. I like to make the disk almost as big as the bag so that it doesn't move around in the bag too much.

Here's a Monti frag on a frag plug inserted into a hole in the disk. It fits VERY snugly so it won't fall out:




Here's a Candy Cane who's skeleton is inserted into the disk (also very snugly) and an elastic band holding it, just in case.




Close the bag up, and put a double elastic on it wrapping it as tight as you can, then fold the end over and wrap some more. The bag should be TIGHT with air.

This one shows the disk with a coral hanging under it:




Put the bag into your box being sure that there is at least one layer of peanuts under the bag, and lots all around it. There should be enough that so that the bag will not move around. It's not a worry if there are no peanuts on the top because the heat pack will be there warming the air up anyway.




Close the garbage bag with a knot, and tuck the knot in the side of the box so that it's not between the lid and the fish bags.
__________________
~ Mindy

SPS fanatic.


Last edited by Myka; 05-05-2008 at 04:27 AM. Reason: To add more thoughts...
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 07:56 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.