Newbie 75 gallon - Page 4

dino · #31 04-03-2018, 07:47 PM

I would never get a clown again. one time it actually went into my net and I contemplated getting rid of it. I kept it though because it was my first fish

Llorgon · #32 04-04-2018, 04:02 AM

Quote:

Originally Posted by dino

I would never get a clown again. one time it actually went into my net and I contemplated getting rid of it. I kept it though because it was my first fish

Sounds like clown fish are kind of hit and miss. What did the clown do?

Sent from my Nexus 6 using Tapatalk

Llorgon · #33 04-05-2018, 08:50 PM

Did some more water tests last night.

Phosphate - 0
pH - 8.0
Ammonia - 0.50ppm
Nitrite - 0
Nitrate - 0
Salinity - 1.025
Temp - 79F

Up to losing about 6 cups of water a day. Hoping to see some nitrates soon.

I have 2 remaining corals in my 10 gallon. Kenya tree and GSP. What is the best dip to use for killing any nuisance algae for when I can finally transfer them to the new tank?

I tried a hydrogen peroxide dip with some other corals that were being overtaken by the red cyno in the 10 gallon and it just killed them...

Llorgon · #34 04-15-2018, 02:44 AM

Bit of a update.

Seeing some nitrate in the tank still no nitrite and I still have some ammonia so coming along slowly.

Bought a atk auto top off system today. So now I won't have to top off the sump every night. What do people use for reservoirs?

I have a big water cooler jug that would fit in the stand, but there wouldn't be room for the electronics.

Might have to make a little electronics cabinet to go beside the tank...

Sent from my Nexus 6 using Tapatalk

Llorgon · #35 04-22-2018, 02:45 AM

Tested the water again today. Cycle is well on it's way. Have started to see some nitrates.

Phos - 0
pH 8.0
Ammonia 0.25
Nitrite 5.0
Nitrate 5.0-10

Sent from my Nexus 6 using Tapatalk

DKoKoMan · #36 04-22-2018, 04:56 AM

Sweet! Almost at the home stretch now.

Llorgon · #37 04-22-2018, 05:34 AM

So I setup the atk auto top off system. Plugged it in, blue light came on, filled a bit, pump turned off seemed to be all good. Few mins later alarm went off. I unplugged and plugged it back in after checking connections, nothing looked out of place. Few minutes later alarm again!

It seems to go off every 10 mins, single beep.

From the atk website I can see what should trigger the alarm.

1. Your ATK has run for more than 5 minutes. This will be true anytime power is applied to the FMM and there are less than 5 fills completed by your ATK. In this condition the FMM will alarm a single long beep.

- it has done less than 5 fills, alarm is a single reoccurring beep. Not a long beep

2. If your ATK has had an opportunity to activate the IQ Fill safety feature. IQ-Fill will become active after the FMM has learned your aquariums normal filling behavior. This takes 5 fill-ups before becoming true. In this condition the FMM will alarm a single long beep.

- again not the same beep, hasn't done 5 fills.

3. Your top level sensor has been covered for more than 10 minutes. Your top level sensor will turn off your PMUP immediately, but will not create an alarm condition until it has been covered for more than 10 minutes. In this condition the FMM will alarm with two beeps.

- time is about right. Alarm goes off every 10 mins, but it's only one beep.

4. Your optional sensor plugged into input #4 is no longer under water. This could be an additional low level optical sensor in your ATK reservoir or in your sump. In this condition the FMM will alarm with four beeps.

- I have nothing plugged into input #4.

5.Your optional sensor plugged into input #3 is under water or wet. This could be a leak detection probe or an additional high level optical sensor placed in your sump. In this condition the FMM will alarm with three beeps.

- I have nothing plugged into #3.

I attached images of my setup. Maybe someone can see what's wrong.

Sent from my Nexus 6 using Tapatalk

DKoKoMan · #38 04-22-2018, 05:52 AM

I bought this for my new tank. Install the antisiphon piece that came with the Neptune ATK. Since the module is in the water at all times it will slowly siphon raising your water level over top top sensor (10 mins) and the alarm is triggered.

Llorgon · #39 04-22-2018, 05:56 AM

I have the siphon break installed. It's above the water level in the reservoir.

I have my water level marked in the sump and it hasn't moved at all. Well, not since I turned it on the first time, it filled a bit, then stopped. Other than that it was plugged in for 30 mins and no change to the water level. But the alarm was still going off every 10 mins.

Sent from my Nexus 6 using Tapatalk

DKoKoMan · #40 04-22-2018, 06:07 AM

It’s a PItA ... I think I have mine dialed in and out of no where I will hear the darn beeping. Too early to tell but I think since I installed the siphon break it may be good. I’m running it out of a 5g pail as I’m waiting for my ATO container. I’m scared to adjust or touch this thing.