Forum: Tank Journal
02-18-2020, 05:13 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
02-17-2020, 05:26 PM
|
Replies: 33
Views: 28,249
I was thinking about that, but frag tank would...
I was thinking about that, but frag tank would have to be a whole separate tank for itself. I dont have room for frag tank close to the DT. I have a tank already for it, but need to figure out if I...
|
Forum: Tank Journal
02-17-2020, 03:48 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
02-17-2020, 07:33 AM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
02-10-2020, 09:19 PM
|
Replies: 33
Views: 28,249
Finally have an update. Weather has been crappy...
Finally have an update. Weather has been crappy and cold last few months, and since I do most of the work in the garage, it was cold. That prevented me from doing much. I finished light mount, or at...
|
Forum: Tank Journal
11-24-2019, 05:26 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
11-21-2019, 05:28 PM
|
Replies: 33
Views: 28,249
Yes, valid point for sure. If it works out as I...
Yes, valid point for sure. If it works out as I have it planned in my head, it should be easy enough to raise or remove as well for cleaning and maintenance. Bracket is quite light, and Noopsyche K7...
|
Forum: Tank Journal
11-21-2019, 03:39 PM
|
Replies: 33
Views: 28,249
I was thinking about welding to begin with, but...
I was thinking about welding to begin with, but dont have access to anyone with welder setup for aluminum. Brazing should produce similar results I hope. Not as strong of course, but whole frame is...
|
Forum: Tank Journal
11-17-2019, 06:28 AM
|
Replies: 33
Views: 28,249
I started working on light mount for the...
I started working on light mount for the Noopsyche K7 Pro IIs that I will be using. I bought aluminum square tubing for this build. I cut tubing at 45 degree angles and used flat corner braces to...
|
Forum: Tank Journal
11-07-2019, 05:59 AM
|
Replies: 33
Views: 28,249
In all honesty I think it may be a blessing in...
In all honesty I think it may be a blessing in disguise, as it will force me to take things slow, and not add a lot all at once. It would give me 6 months or so after putting things in to leave it...
|
Forum: Tank Journal
11-07-2019, 03:16 AM
|
Replies: 33
Views: 28,249
Truth be told I couldnt see swirl marks from...
Truth be told I couldnt see swirl marks from buffing. I was using Dual Action polisher for it, so maybe that helped. I think that once water goes in, it will be crystal clear. When I got it, back was...
|
Forum: Tank Journal
11-06-2019, 10:54 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
11-01-2019, 07:52 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
11-01-2019, 07:51 PM
|
Replies: 33
Views: 28,249
Another thing I never did was buff/polish. Not...
Another thing I never did was buff/polish. Not just acrylic, but anything at all. Again I spent about a week reading up various forums, watched videos and so on. I decided I will use Novus 3, 2 and 1...
|
Forum: Tank Journal
11-01-2019, 07:50 PM
|
Replies: 33
Views: 28,249
|
Forum: Tank Journal
11-01-2019, 07:48 PM
|
Replies: 33
Views: 28,249
5 Feet, 110 Gallons of Fun
Hello everyone, I figured it would be good to start my own build thread for several reasons. I got a lot of ideas and help from various folks on Can Reef last time around and so far, so I would like...
|