Profilux 3.1 controller setup
 

For sale a profilux 3.1 setup includes the following:

Two head units, one has a slightly garbled screen (this screen would work fine with a little DIY, I noticed that if you take it apart and hold the screen at a certain angle it clears up perfectly, most likely simple fix) but perfectly suitable as a backup. The other is fine.
3 head dosing pump
2 PAB power bars
2 non-PAB power bars
Vortech module
Leak detection module with once sensor
Profilix touch with profilux touch module
3 level sensors, one mechanical the other two optical
2 LED simuspot modules for moonlight, sunrise/sunset and lightning storm effects.
GHL temp probe and salinity probe, both light use and perfectly fine, calibrate to spec no problem. Might be a generic pH probe as well, not sure if I am keeping this one for my new setup as it is brand new and in water for only a couple weeks.
Other odds and ends, cables etc.

Everything working fine, I am upgrading.
Take everything for $1200, only selling as a set at this time.

Bump. Open to offers.

Forgot to indicate that the primary head unit has the PL-ADIN card installed.

Realize the significant cash outlay here but there is a lot included! The profilux touch alone is around 400 to buy new. Head units have significant signficant value and the doser is not cheap. Vortech controller is around 200.

Open to offers!

Will break this up into a set and then some spare parts.

Set:
Profilux 3.1 head unit with ADIN card
1 PAB power bar
1 non-PAB power bar
Temperature and pH sensors
Conductivity probe
3 GHL float switches with float switch holder (tab broken on one of the brackets but still works)
Avast marine probe and tubing holders
All necessary writing etc.
$600

Extras:
Spare head unit with slightly garbled screen $100
PAB power bar $150
Non PAB power bar $100
Profilux touch with module $300
3 head original doser $200
Vortech module $100
Leak detection module with sensor $80
2 simuspot LEDs $150

Prrice reductions on some items as below:

Set:
Profilux 3.1 head unit with ADIN card
1 PAB power bar
1 non-PAB power bar
Temperature and pH sensors
Conductivity probe
3 GHL float switches with float switch holder (tab broken on one of the brackets but still works)
Avast marine probe and tubing holders
All necessary writing etc.
$550

Extras:
Spare head unit with slightly garbled screen $100
PAB power bar $150
Non PAB power bar $100
Profilux touch with module $250
3 head original doser $150
Vortech module $100
Leak detection module with sensor $80
2 simuspot LEDs $120

Willing to entertain offers on breaking up the parts of the set as well.

bump

Price reductions on some items as below: Price for set listed below individual items.

Set:
Profilux 3.1 head unit with ADIN card $250
1 PAB power bar $150
1 non-PAB power bar $100
Temperature and pH sensors $20 each
Conductivity probe $100
3 GHL float switches with float switch holder (tab broken on one of the brackets but still works) $20 each or $50 for all three
Avast marine probe and tubing holders
All necessary wiring etc.
$500 for set listed above

Extras:
Spare head unit with slightly garbled screen $100
PAB power bar SOLD
Non PAB power bar $100
Profilux touch with module $200
3 head original doser $150
Vortech module $100
Leak detection module with sensor $70
2 simuspot LEDs $100

Willing to entertain offers on breaking up the parts of the set as well.

Sold one PAB power bar, rest still available

ADIN card and temp probe sold . Head unit price reduced to $225.

Bump, still lots of profilux parts left

Feel free to make offers!