Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Reef (http://www.canreef.com/vbulletin/forumdisplay.php?f=8)
-   -   upgrading-advice welcome! (http://www.canreef.com/vbulletin/showthread.php?t=11601)

richtg 10-12-2004 06:34 AM

upgrading-advice welcome!
 
I am on the verge of bumping up to a 90 gal/45sump for my ever-expanding reef. I am on a budget (aren't we all) and here is what I have come up with so far:

-hesitant to buy a used tank (heavy metals...) new @ inter-american for $150 + drilling. I have the 45, so I need a stand to hold both. I like DIY's, but sometimes it's more economical to buy pre-fab. Any ideas?

-My third experimental painted wood canopy is not standing up. (I use fluorescents, so the built up humidity finds it's way through each type of paint I've tried. Any suggestions for a good hood-type canopy or paint?

-I need a good pump to move 1000+gph for <$250.

-I bought my oolitic sand bulk from Danny Wai and like it. I will buy more unless someone has some to sell me. A bit more LR, perhaps...

-finally, I would like to buy some new pc's. Where is a reasonable deal to be found in town or the internet. Any bad experiences from buying lights on the net?

Thank you for your time and valuable advice to clatter around in my brain. Rich. :eek:

danny zubot 10-12-2004 04:42 PM

reply
 
Christmas is coming, you might want to hold off on buying lights for the meantime. Hint Hint :mrgreen:

I have been thinking about going MH for a while now, and if I do I won't have a canopy. I think we should just build an open crown for the tank, better for heat dicipation anyway.

bear27 10-12-2004 09:50 PM

For your pump a mag 12 or 18 would fit the budget

richtg 10-13-2004 07:44 PM

Thanks, guys. Who makes the "mag" series pumps?

Buccaneer 10-14-2004 12:03 AM

Quote:

Originally Posted by richtg
Thanks, guys. Who makes the "mag" series pumps?

Danner I believe

richtg 10-15-2004 11:33 AM

I've also been researching a rock wall back using foam and LR, sand, shells, etc. Any warnings or ideas?

IslandReefer 10-15-2004 02:23 PM

foam wall
 
Look into European Reefs...they seem to like the foam back wall.....no problems that I am aware of....except you are stuck :biggrin: with it .

christyf5 10-15-2004 04:07 PM

The foam doesn't leach anything back into the water??

Christy :)

reefhawk 10-16-2004 05:39 AM

try marine enamel for paint that stands up to salt water.

richtg 10-17-2004 09:36 PM

Thanks. Once the foam ('Great Stuff') is fully cured, it is inert. It will break down slowly if exposed to U.V. over time, but it is harmless. People have been doing this for years and found that if you use a good marine paint, it lasts. There is a really cool thread on reefcentral.com in the DIY section.

P.S. I ordered my custom Starfire euro 90 gal from Bow Valley Aquariums. WHOOOOOOOOOHOOOOOO!!!!!!!!!!

danny zubot 10-26-2004 04:02 PM

reply
 
He Dude! you should take pictures of your progress while building that tank, and post them for all to see. Gonna be a smokin' reef!

richtg 11-05-2004 11:07 PM

Here is a photo of the plumbing on my new tank
http://www.canreef.com/photopost/dat...g-med.jpg?5544
and here is the foam wall after sculpting around the overflows and all 16 return holes. I used about 5lbs of dried LR in the wall for a more natural look as well as some ledges to place frags on. The foam is coated with 5 coats of marine enamel and everything was allowed to cure for a week. Here is the finished wall.
[/img]http://www.canreef.com/photopost/data/508/1107foamrockwall-med.jpg?7505[/IMG]
It's hard to see the detail, but the depth of the foam varies between 1/2" and 4". Here is a pic of the tank with the LR and corals in it.
http://www.canreef.com/photopost/dat...f-med.jpg?4070
I kept all the coraline shavings from the old tank (new sump) and spread onto the foam wall. Should be saturated in a few months. [/img]

richtg 11-05-2004 11:09 PM

Argh! I have to figure out the pic posting process for this site!

richtg 11-05-2004 11:20 PM

bear with me here...
http://reefcentral.com/gallery/data/...nkplumbing.jpg

muck 11-05-2004 11:52 PM

Quote:

Originally Posted by richtg
Argh! I have to figure out the pic posting process for this site!

If you edit your post and remove anything after ".jpg" the pictures should show up. :biggrin:

Like so...

Quote:

Originally Posted by richtg
Here is a photo of the plumbing on my new tank
http://www.canreef.com/photopost/dat...umbing-med.jpg
and here is the foam wall after sculpting around the overflows and all 16 return holes. I used about 5lbs of dried LR in the wall for a more natural look as well as some ledges to place frags on. The foam is coated with 5 coats of marine enamel and everything was allowed to cure for a week. Here is the finished wall.
http://www.canreef.com/photopost/dat...ckwall-med.jpg
It's hard to see the detail, but the depth of the foam varies between 1/2" and 4". Here is a pic of the tank with the LR and corals in it.
http://www.canreef.com/photopost/dat...amreef-med.jpg
I kept all the coraline shavings from the old tank (new sump) and spread onto the foam wall. Should be saturated in a few months.

cheers

Invigor 11-06-2004 12:22 AM

that is incredibly awesome!!

richtg 11-06-2004 04:02 AM

Thanks, Ryan. I'll have to find a sticky thread about posting pics on this site.

richtg 11-06-2004 04:04 AM

Thanks, Invigor! :mrgreen:

richtg 11-06-2004 04:22 AM

I forgot to mention that I picked up a Gen-X Mak 4 pump and I'm totally impressed.


All times are GMT. The time now is 07:22 PM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.