Canreef Aquatics Bulletin Board
Page 78 of 123 « First < 28687677 78 798088 > Last »
Show 40 post(s) from this thread on one page

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Tank Journal (http://www.canreef.com/vbulletin/forumdisplay.php?f=18)
-   -   Lance's 225 gal tank (http://www.canreef.com/vbulletin/showthread.php?t=47331)

Lance 11-13-2010 03:50 PM
Quote:
Originally Posted by fishytime (Post 564343)
those are great little fish Lance.....I love mine......always out and hovering (not like the blue assessor I have in my small tank......I never see it when the lights are on, even though its the only fish in the tank).....and so far my yellow doesnt seem to be too aggressive.....mind you the only fish mine could bully is a tailspot that is the same-ish size but was in the tank before the assessor....

It should do fine in the 90g. His tank mates are a Coral Beauty, smallish Foxface, Ruby Headed Wrasse, 2 Percs, PJ Cardinal, Yellow Watchman Goby, and two cleaner shrimp.

Lance 11-13-2010 05:27 PM
I have a Sedra pump powering two reactors in the sump, which is kind of silly since I have a Barracuda return pump that is only using about 70% capacity. I want to "T" off one of the return lines to feed the reactors.
My question is: How long should I allow the Weld-On P-70 primer and PVC 795 to dry before going back on-line? The can says 30 minutes cure time, but I don't trust that to a tank full of fish and corals. Anybody had any experience using Weld-On on a running tank? 24 hours or less/more?

burrows14 11-13-2010 06:19 PM
You would be good to go in 15 mins. I have used both plumbing a bunch of friends tanks. I always use the prime the fittings and let it dry completly before glueing. Be genourous with the glue and make sure to give the pipe a quater turn to make sure their is no air bubbles and the glue is spread evenly and then use paper towel to wipe off the excess glue. You should have no leaks and a nice clean look that way.

Cheers
Ray

Quote:
Originally Posted by Lance (Post 564400)
I have a Sedra pump powering two reactors in the sump, which is kind of silly since I have a Barracuda return pump that is only using about 70% capacity. I want to "T" off one of the return lines to feed the reactors.
My question is: How long should I allow the Weld-On P-70 primer and PVC 795 to dry before going back on-line? The can says 30 minutes cure time, but I don't trust that to a tank full of fish and corals. Anybody had any experience using Weld-On on a running tank? 24 hours or less/more?

Lance 11-13-2010 06:42 PM
Quote:
Originally Posted by burrows14 (Post 564412)
You would be good to go in 15 mins. I have used both plumbing a bunch of friends tanks. I always use the prime the fittings and let it dry completly before glueing. Be genourous with the glue and make sure to give the pipe a quater turn to make sure their is no air bubbles and the glue is spread evenly and then use paper towel to wipe off the excess glue. You should have no leaks and a nice clean look that way.

Cheers
Ray

Thanks Ray. I wanna make sure I'm understanding you. I've used Weld-On plenty of times. It's not the cure time of the glue or the procedure I'm worried about, it's the effect of the glue on a tank full of animals that worries me. Am I understanding that after 15 minutes of curing there was no problem on an inhabited tank?

Zoaelite 11-13-2010 06:45 PM
WOW those fish can produce a whack load of eggs, ever find any little babies swimmin about? Tanks lookin wicked as usual!

Lance 11-13-2010 06:52 PM
Quote:
Originally Posted by zoaElite (Post 564418)
WOW those fish can produce a whack load of eggs, ever find any little babies swimmin about? Tanks lookin wicked as usual!

Thanks. Nope, I've never seen any babies. They probably hatch out at night and are skimmed off.

lastlight 11-13-2010 07:41 PM
I had finished doing some plumbing on my first tank and I must have let the parts sit drying for at least 30 min. I wanted to know if it was still wet and decided to put my nose to one end of the plumbing and 'take a wiff'.

I damn near fell over everything went black. I don't think I had used more glue than needed either I'm just saying the stuff was still potent. 30 min seems too soon to me.

muck 11-13-2010 08:06 PM
Quote:
Originally Posted by zoaElite (Post 564418)
WOW those fish can produce a whack load of eggs, ever find any little babies swimmin about? Tanks lookin wicked as usual!
No doubt... unbelievable the amount of eggies.
Thanks for the pics Lance.

Lance 11-13-2010 08:10 PM
Quote:
Originally Posted by lastlight (Post 564432)
I had finished doing some plumbing on my first tank and I must have let the parts sit drying for at least 30 min. I wanted to know if it was still wet and decided to put my nose to one end of the plumbing and 'take a wiff'.

I damn near fell over everything went black. I don't think I had used more glue than needed either I'm just saying the stuff was still potent. 30 min seems too soon to me.

Yeah, that's what I'm thinking: If you can still smell it, it's not fully cured. I think I'll leave it until no odor left.

lastlight 11-13-2010 08:13 PM
When you do your nose test just use one nostril that way you can only HALF blackout. It works like that right!?


All times are GMT. The time now is 06:12 PM.
Page 78 of 123 « First < 28687677 78 798088 > Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.