the units are about 12" above water line

no idea on UFO ;)

Thanks Aaron for these amazing photos of his Mitras illuminated tank

5 months old. 4 months under the Mitras.

http://farm6.staticflickr.com/5509/1...4c6237f8_b.jpg
October FTS by --Aaron--

http://farm6.staticflickr.com/5324/1...6428ab8f_b.jpg
October FTS by --Aaron--

http://farm8.staticflickr.com/7368/1...39809b67_b.jpg
Top Down October by --Aaron--

http://farm8.staticflickr.com/7384/1...098e6239_b.jpg
Top Down October by --Aaron--

http://farm6.staticflickr.com/5491/1...4d5f2d48_b.jpg
Stag by --Aaron--

http://farm8.staticflickr.com/7438/1...b4792dfa_b.jpg
Orange Digi by --Aaron--

http://farm8.staticflickr.com/7418/1...025f90d0_b.jpg
Blue Millipora by --Aaron--

http://farm4.staticflickr.com/3737/1...804b5d10_b.jpg
Acropora subulata by --Aaron--

http://farm4.staticflickr.com/3668/1...879310d1_b.jpg
Acropora by --Aaron--

ProfiLux Control 6 is completely renewed with the Light Composer from GHL Control Center.

You will be able to load Mitras *.lpc files in the new version of ProfiLux Control and easily set up the Illumination with ProfiLux Control.

The ProfiLux Computer will work as master and control all your Mitras lamps (they should be set to slave mode).

The thunderstorm synchronisation between ProfiLux and Mitras is also implemented.

Each Illumination channel can be separately controlled and set up directly from ProfiLux Control.

You can also use our smartphone apps to manually control the brightness of each channel.

New versions of profilux control, profilux and mitras firmware will be available to download within a shortly at www.aquariumcomputer.com

What % do you have your red and green at
 

i dont have mitras, and more a diy set up, however want to add green and red led

So now i can putlets say 10 red and 10 green and have them blasting 50% or 5 red and 5 green at 100%

So if you would have them at 50% and you have ..... Number per unit, it gives me some insight in how many i would use at 100%

Reason for this is becouse i have all my dimming drivers in use, and have a few CC drivers left

Hi
You can set the mitras LED channels to anything you wish if you only wish to run reds and greens then this is fine just set the rest of the channels to 0% you can then adjust the red and green channels to any % intensity you wish.

I do understand that each channel can go from 0 to 100

Question is, what douse men have the red and green at,

I know this is preference, however if the average has them at 20%and there would be 7 above a tank, than in my case it would be the same as 1 at 100% (+- whatever my preference is.

Same is if in general thy have them at 50% than i would have some indication that maybe I should use 3 at 100% for each 6 at 50% on he mitras.

Sorry, the factory build units are out of my budget, and i already have a 200+ led rig, that I want to adjust a bit in to a full spectrum Unit

does anyome have some other specrturms that I can try say like the 8-10-12K range.. that is already done with a nice night time illumation
i thought that if I go that route i could raise my light a bit. for more of the spread.

Looks lime Elf on the shelf has gone fishing of the Mitras this Xmas!

https://fbcdn-sphotos-c-a.akamaihd.n...58027125_o.jpg

But wait, looks like Elfie is into a whopper!

https://fbcdn-sphotos-f-a.akamaihd.n...71925598_o.jpg

check back to see what Elfie has caught everyone ;)

Look what Elfie caught!!! a nice pair of Mitras Sunglasses! Well done Elfie nice catch!

https://fbcdn-sphotos-g-a.akamaihd.n...23614834_o.jpg